Slab Leak Detection and Repair in Jupiter, FL
A leak in a pipe under the concrete floor is found with a meter test and listening gear, then fixed by a spot repair, a reroute, or a repipe.
- Under-slab pinpointing
- Spot repair, reroute, or repipe
- Price before work
- 24/7 phone line
Warm Floor or Running Water With Nothing On?
Most calls about this problem start with something odd rather than a name. A patch of tile that feels warm underfoot, a water meter that spins with every tap closed, or a faint hiss at night all point to the same cause: a pressurized pipe leaking under the concrete.
The good news is that the leak can be located without breaking up the whole floor. The job is to find the exact spot, then choose between a small repair and a larger fix.
What a Slab Leak Is
A slab leak is a leak in a water supply or drain pipe that runs under or inside a concrete slab foundation. Slab-on-grade construction is the norm across South Florida, so supply lines often run through or beneath the concrete instead of through an open crawlspace.
Hot-water lines are common culprits because heat and expansion stress the pipe, and the warm spot on a floor is the classic sign. Cold-water leaks are harder to feel and usually show up first as a bill or a meter reading.
Three Ways to Fix a Line Under the Slab
The right fix depends on how many leaks there are, the pipe material, and how much of the floor you are willing to open.
| Option | What it involves | Trade-off |
|---|---|---|
| Spot repair | Open the slab at the pinpointed leak, cut out the bad section, and replace it | Quickest, but another leak may follow if the pipe is aging |
| Reroute | Abandon the leaking run and install a new line through the attic or walls | Avoids concrete work, but opens walls and ceilings |
| Repipe | Replace the whole supply system, often with PEX | Highest upfront cost, best when leaks keep returning |
Meter Spinning With Everything Off?
Call the 24/7 line. Close the main shutoff in the meantime.
How the Spot Is Pinpointed
Meter test
Confirm a leak exists and that it is on the house side.
Hot or cold
Isolate each line to learn which one is losing pressure.
Listen and scan
Acoustic gear and thermal imaging track the sound or heat to a small area.
Mark it
The spot is marked on the floor so any opening stays as small as possible.
Choose the fix
You get the repair options and a price before anyone touches the slab.
Why Slab Leaks Show Up in Jupiter Houses
Jupiter grew from 3,136 residents in 1970 to 24,986 in 1990, per U.S. Census counts, so a large share of its older houses were built in those two decades. Copper supply lines in that period can develop pinhole leaks with age, and polybutylene pipe, widely installed nationally from about 1978 to 1995, can fail at its fittings.
Permits matter on the bigger fixes. The Town of Jupiter Building Department at 210 Military Trail handles permits inside town limits, and Palm Beach County covers unincorporated areas such as Jupiter Farms. The Florida Building Code, Plumbing, which is based on the International Plumbing Code (IPC), governs the work. Florida Statutes Chapter 489 requires construction work to be done by a licensed contractor, so ask who pulls the permit before you sign.
Cost and permits are easier to plan when the leak is found early. A slow leak here can undermine soil under the slab and run up a water bill for months before the first stain appears.
If You Suspect a Slab Leak
Close the main
Shutting the main valve stops the loss while you wait.
Switch off the heater
If a hot-water line is involved, turn off power or gas to the water heater so it does not run dry.
Note the spots
Mark warm tiles with painter's tape so the technician can see where you felt heat.
Check your policy
Read the water damage and seepage terms before deciding how much of the floor to open.
What Drives a Slab Leak Price
Coverage for slab leaks varies. Some policies pay for the access cost to reach a covered leak, and others exclude water that escaped over time. Ask your insurer before choosing the repair.
Slab Leak Calls Across the Area
Slab leak calls come in from 33458, 33469, 33477, and 33478. Older 1970s and 1980s houses in central Jupiter drive many of them. Juno Beach (33408), Palm Beach Gardens (33410 and 33418), and Hobe Sound (33455) follow similar patterns.
The Palm Beach Gardens page notes the mix of housing eras there.
Where Slab Leaks Turn Up: Indian Creek, Jonathan's Landing, and Beyond
Slab-on-grade construction is the norm across South Florida, and Jupiter is no exception. Indian Creek alone holds 12 subdivisions, and Jonathan's Landing opened its first villages in 1979. Houses from those decades have had supply lines under the concrete for thirty to forty years.
A warm patch on tile in any of these communities is worth a call the same day. Slab leaks near the river or the Intracoastal can also soak the soil before they reach the surface, so the pinpoint comes before any cutting.
Before and After the Repair
If you only suspect a leak and want to confirm it first, start with hidden leak location. A leak that has already soaked the floor may also need drying and restoration to dry the subfloor and walls. A failed line is also covered under split supply line repair when the pipe has fully let go. If leaks keep returning, whole-home repiping replaces the supply system.
Slab Leak Detection & Repair Questions From Jupiter
Common signs are a sudden jump in the water bill, a warm spot on a tile floor, the sound of water with every fixture off, low pressure, and a meter that moves when nothing is running.
Yes. Meter testing, isolation, and listening or thermal gear narrow the spot, so any opening is small.
Not usually for a spot repair. A reroute or repipe can interrupt water for part of a day, and the technician will say so before work begins.
Hot-water leaks are common under slabs. Turn off the water heater and close the main, then call the 24/7 line.
Reroutes and repipes generally do. Inside town limits that is the Town of Jupiter Building Department, and in unincorporated areas it is Palm Beach County.
Treat it as one if water is visible or the meter is spinning fast. Even a slow leak causes damage, so it is better not to wait.